20mm x 4.0mm Coloured Double Countersunk Wood Screws - RAL Powder-Coated BZP Steel

(No reviews) Write a Review
Selected Step Two: Select Colour is
Screw Length: 20mm
Thread Size: 4mm M4
Material: BZP Steel
Head Type: Countersunk Head
Recess: Pozi PZ2
Thread Type: Self Tapping
colour_count: 40
tech_thread_type: Self tapping
tech_head_style: Countersunk Head
tech_drive_type: Pozi PZ2
tech_length: 20mm
tech_diameter: 4mm
tech_material: BZP Steel
tech_coating: Premium powder coat
tech_colour_system: RAL Classic
  • Guaranteed Colour Match

    Matched to RAL Classic colours

  • In-House Experts

    We know our products

  • Durable Finish

    Dual layer powder coating

  • Same-Day Despatch*

    Order before 12pm

* Same-day despatch applies to stocked items only. Contact us if you need your order sooner than the stated lead time. Product images are for illustration only and should not be relied on as an accurate colour match – request a physical sample for an exact match.

20mm x 4.0mm Coloured Double Countersunk Wood Screws - RAL Powder-Coated BZP Steel
20mm x 4.0mm Coloured Double Countersunk Wood Screws - RAL Powder-Coated BZP Steel
£0.13

20mm x 4.0mm Coloured Double Countersunk Wood Screws - RAL Powder-Coated BZP Steel

£0.13

Description

These 4.0mm x 20mm coloured double countersunk wood screws are a short, single thread chipboard and wood screw for thin timber, man-made boards and, with a plastic plug, light fixings into masonry. The carbon steel screw is zinc plated and powder coated to a RAL Classic colour, so the head matches the board, trim or fascia instead of showing as a bright zinc dot.

The coarse thread is preferred for woodworking. The 40° deep single thread gives a secure fixing with high pull-out resistance, and the 25° sharp point and single lead give a fast start and improved thread acceptance. The double countersunk head is designed to reduce the likelihood of head shear and to help the screw sit flush, and the PZ2 Pozidriv recess gives a firm grip for the driver.

At 20mm and fully threaded they suit thin panels, trim and light hardware where a longer screw would break through the back, and are used by joiners, sign makers and installers who want a clean, colour-matched finish.

40 RAL Colour-Matched Finishes

Each screw is powder coated to a RAL Classic standard and oven cured. The finish gives a hard, uniform colour that stays consistent from one bag to the next, so a run of fixings across a board or frame looks even.

40 RAL colours are stocked for dispatch, covering whites, yellows, reds, purples, blues, greens, greys, browns and blacks. If your project calls for a colour outside the stocked set, contact us with your RAL reference for availability and lead times.

Site Applications

Where these 4.0mm x 20mm coloured wood screws are most often used:

  • Thin timber, trim and cladding battens
  • Chipboard and MDF panels and boards
  • Cabinetry, small hinges and brackets
  • Signage backing boards and light fittings
  • Light fixings to masonry with plastic plugs
  • Painted or coloured surfaces where the fixing should stay discreet

Specification

Specification at a glance:

Screw Type Single thread wood and chipboard screw
Head Type Double countersunk
Drive Pozidriv PZ2
Gauge No. 8 (4.0mm)
Thread Diameter 4.0mm
Core Thread Diameter 2.5mm
Length 20mm
Thread Coverage Fully threaded
Thread Length 15mm
Thread Type 40° deep single thread
Point 25° sharp point
Suitable Substrates Softwood, chipboard, MDF, masonry (with plug)
Pilot Hole 2.5mm
Clearance Hole 4mm
Material Carbon steel
Plating Zinc plated
Coating RAL Classic powder coat
Colours Available 40 stocked RAL colours

Frequently Asked Questions

What are these wood screws used for?

Fixing into thin timber and man-made boards where a short screw will not poke through the back: trim and cladding battens, signage backing boards, cabinetry, small hinges, brackets and light fittings. With a suitable plastic plug they also fix light items to masonry. The double countersunk head sits flush, and the RAL powder coat keeps the fixing discreet on painted or coloured surfaces.

What size are they?

4.0mm x 20mm, which is a No. 8 gauge screw. The thread is 4mm, the core thread diameter is 2.5mm, and the thread length is 15mm. If a spec calls for a 4 x 20 countersunk wood or chipboard screw, this is that size with a powder coated head.

What does double countersunk mean?

The head has a countersunk top and a second angled step underneath. The supplier designs it to reduce the likelihood of head shear and to help the screw finish countersinking, so the head sits flush with a neat finish in timber and boards.

Do I need to drill a pilot hole?

For best results, yes. Drill a 2.5mm pilot hole (the core thread diameter), especially in hardwood, dense board or near an edge, and countersink the head if the material is hard. Test one screw in your material first. Drive with a PZ2 Pozidriv bit held square to the screw.

Will two pieces of timber pull together?

These screws are fully threaded, so the thread also grips the top piece and can hold the two pieces apart. To pull them tight, drill a 4mm clearance hole through the top piece so the thread only bites in the lower piece, then add the 2.5mm pilot hole below it.

Can I fix into masonry?

Yes, with a plastic wall plug, for light fixings. Drill the masonry to the size the plug manufacturer specifies for a 4mm screw, push the plug in flush, and drive the screw through the item into the plug. Check the plug is suitable for your wall type.

Can I use these outdoors?

These screws are rated by the supplier for clean, dry, low-humidity environments, so they are best used indoors or in protected, dry locations. The powder coat adds a protective layer, but for external, damp or exposed fixings choose a stainless steel screw instead.

What driver bit do I need?

A PZ2 Pozidriv bit. Use a genuine PZ2 rather than a Phillips bit, which sits less securely in the recess and is more likely to cam out and mark the coloured head.

Can I choose a specific RAL colour?

Yes. 40 RAL Classic colours are stocked for dispatch, and the full list is shown on this page. If your project needs a colour outside the stocked set, contact us with your RAL reference for availability and lead times.

Powder Coated Wood Screws

Colour-matched fixings are all we do. Each screw is finished to a RAL reference, so the colour you order is the colour on the screw.

Electrostatically applied and heat cured, powder coating produces a harder, thicker and more durable finish than wet paint. On a fixing that is seen up close and expected to stay looking right, that difference is the whole point.

Benefits of powder coated wood screws:

  • Scratch resistant
  • Rust resistant
  • UV resistant
  • Weather resistant
  • Colourfast

Available RAL Colours

These 4.0mm x 20mm coloured double countersunk wood screws are stocked in the following 40 RAL Classic colours. Select your colour from the options above, or view the full RALfixings colour guide for additional RAL colours available on request.

  • RAL 1013 Oyster White
  • RAL 1015 Light Ivory
  • RAL 1016 Sulphur Yellow
  • RAL 1019 Grey Beige
  • RAL 1020 Olive Yellow
  • RAL 1023 Traffic Yellow
  • RAL 1033 Dahlia Yellow
  • RAL 1036 Pearl Gold
  • RAL 3002 Carmine Red
  • RAL 3004 Purple Red
  • RAL 3009 Oxide Red
  • RAL 3020 Traffic Red
  • RAL 4006 Traffic Purple
  • RAL 4007 Violet Purple
  • RAL 4010 Telemagenta
  • RAL 5003 Sapphire Blue
  • RAL 5004 Black Blue
  • RAL 5012 Light Blue
  • RAL 5013 Cobalt Blue
  • RAL 5023 Distant Blue
  • RAL 5024 Pastel Blue
  • RAL 6003 Olive Green
  • RAL 6005 Moss Green
  • RAL 6012 Black Green
  • RAL 6016 Turquoise Green
  • RAL 6024 Traffic Green
  • RAL 6025 Fern Green
  • RAL 6027 Light Green
  • RAL 7009 Green Grey
  • RAL 7016 Anthracite Grey
  • RAL 7032 Pebble Grey
  • RAL 7035 Light Grey
  • RAL 7038 Agate Grey
  • RAL 7042 Traffic Grey A
  • RAL 8004 Copper Brown
  • RAL 8008 Olive Brown
  • RAL 8019 Grey Brown
  • RAL 9005 Jet Black
  • RAL 9010 Pure White
  • RAL 9016 Traffic White
tech_thread_type Self tapping
tech_head_style Countersunk Head
tech_drive_type Pozi PZ2
tech_length 20mm
tech_diameter 4mm
tech_material BZP Steel
tech_coating Premium powder coat
tech_colour_system RAL Classic

Recommended applications

A short, colour-matched 20mm wood screw for thin timber, trim, cladding battens, chipboard and MDF, plus cabinetry, small hinges, brackets and signage backing boards. With a plastic plug it also fixes light items to masonry. The double countersunk head sits flush, and the powder coat keeps the fixing discreet on coloured surfaces.

Drill a 2.5mm pilot hole, countersink the head if the material is hard, and drive with a PZ2 Pozidriv bit held square to the screw. These screws are fully threaded: to pull two pieces together, drill a 4mm clearance hole through the top piece first. For masonry, use a plug suitable for a 4mm screw and your wall type.

The supplier rates these screws for clean, dry, low-humidity locations, so use them indoors or in protected dry areas; for external or damp fixings choose a stainless steel screw. This product covers all 40 stocked RAL colours.

Suitable for

Thin Timber & TrimShort 20mm length will not break through thin panels
Chipboard & MDFFlush double countersunk heads in a matching RAL colour
Cabinetry & Light HardwareSmall hinges, brackets and fittings with a neat head
Signage Backing BoardsColour-matched fixings on frames and boards
Masonry (with Plug)Light fixings into brick or block walls

Loading delivery information...

Certificate of Conformity
ISO 9001 Approved
60+ RAL Colours
Fast UK Despatch

Don't see your RAL colour listed above? Contact us to request a RAL Colour.