22mm x 4.8mm Coloured Wafer Head Self-Drilling Screws - RAL Powder-Coated BZP Steel
Available in 40 colours
Our multipurpose 38mm x 4.8mm painted countersunk self-tapping screws are used for stitching metal sheets together, attaching thin sheet metal to metal and general light fabrication. These colour-matched screws have a 60° self-tapping thread and a sharp AB point for easy insertion into a pre-drilled hole, while the countersunk head gives a discreet finish into pre-countersunk holes.
The carbon steel screw is plated in trivalent chromium (Cr3) zinc, then the head is powder coated to a RAL Classic colour so it matches the sheet around it instead of showing as a bright zinc dot. Drive it with a PZ2 Pozidriv bit, and make sure a pilot hole is drilled first, as these self-tapping screws are not self-drilling.
At 38mm and fully threaded they suit lapped sheets, trims and brackets, and are used by cladders, sign makers, hoarding installers and fabricators who want a clean, colour-matched finish.
Each screw head is powder coated to a RAL Classic standard and oven cured. The finish gives a hard, uniform colour that stays consistent from one bag to the next, so a run of fixings across a sheet or panel looks even.
40 RAL colours are stocked for dispatch, covering whites, yellows, reds, purples, blues, greens, greys, browns and blacks. If your project calls for a colour outside the stocked set, contact us with your RAL reference for availability and lead times.
Where these 38mm x 4.8mm countersunk self-tapping screws are most often used:
Specification at a glance:
| Screw Type | Self-tapping screw, countersunk head |
| Diameter | 4.8mm (gauge 10 / No. 10) |
| Length | 38mm (1 1/2 inch) |
| Imperial Size | 10 x 1 1/2 |
| Head Type | Countersunk |
| Drive | Pozidriv PZ2 |
| Thread | 60° self-tapping |
| Thread Coverage | Fully threaded |
| Point | AB point |
| Pre-Drilled Hole | Required |
| Suitable Substrates | Steel, thin sheet metal |
| Material | Carbon steel |
| Plating | Zinc plated, clear Cr3, before the heads are powder coated |
| Standard | Manufactured to BS 4174 |
| Coating | RAL Classic powder coated head |
| Colours Available | 40 stocked RAL colours |
Stitching metal sheets together and attaching thin sheet metal to metal: cladding and flashing trims, signage panels and frames, hoarding, brackets and light fabrication. The countersunk head gives a discreet finish, and the RAL powder coat matches the head to the sheet so the fixing blends in.
Yes. These are self-tapping, not self-drilling, so a pre-drilled hole is required. Drill a pilot hole slightly smaller than the 4.8mm thread, commonly around 4.0mm to 4.2mm in thin sheet steel, then drive the screw in and it forms its own thread. The right size depends on the material and its thickness, so test one screw first.
No. The supplier designs the countersunk head to give a discreet finish into pre-countersunk holes, so the hole needs to be countersunk or dimpled first for the head to sit flush. If the head is left standing proud, the colour is still visible but the fixing will not be flush.
The AB point is a sharp, tapered tip with a 60 degree self-tapping thread that cuts into a pre-drilled hole in thin sheet metal. A self-drilling (tek) screw has a drill tip and makes its own hole. If you want to drive straight into steel without drilling, choose one of our coloured self-drilling screws instead.
A PZ2 Pozidriv bit. Use a genuine PZ2 rather than a Phillips bit, which sits less securely in the recess and is more likely to cam out and mark the coloured head. Keep the driver square to the screw and use firm, even pressure.
They all describe the same screw. 4.8mm is the thread diameter (gauge 10, also written No. 10), and 38mm is the length, which is 1 1/2 inches. So a 10 x 1 1/2 and a 4.8 x 38 are the same size.
For general exterior fixing the zinc plating and the powder coated head give protection. For constantly wet, marine or coastal locations, or where cut or drilled edges will be exposed, choose a stainless steel screw instead.
Yes. 40 RAL Classic colours are stocked for dispatch, and the full list is shown on this page. If your project needs a colour outside the stocked set, contact us with your RAL reference for availability and lead times.
Colour-matched fixings are all we do. Each screw head is finished to a RAL reference, so the colour you order is the colour you see on the head.
Electrostatically applied and heat cured, powder coating produces a harder, thicker and more durable finish than wet paint. On a fixing that is seen up close and expected to stay looking right, that difference is the whole point.
Benefits of powder coated self-tapping screws:
These 38mm x 4.8mm coloured countersunk self-tapping screws are stocked in the following 40 RAL Classic colours. Select your colour from the options above, or view the full RALfixings colour guide for additional RAL colours available on request.
| tech_thread_type | Self tapping |
|---|---|
| tech_head_style | Countersunk Head |
| tech_drive_type | Pozi PZ2 |
| tech_length | 38mm |
| tech_diameter | 4.8mm |
| tech_material | BZP Steel |
| tech_coating | Premium powder coat |
| tech_colour_system | RAL Classic |
A colour-matched countersunk self-tapping screw for stitching metal sheets and fixing thin sheet metal to metal: cladding and flashing trims, signage panels and frames, hoarding, brackets and light fabrication. The 38mm length reaches through lapped sheets, and the countersunk head gives a discreet finish in a RAL colour that matches the surface.
Drill a pilot hole first, commonly around 4.0mm to 4.2mm in thin sheet steel, and countersink or dimple it so the head sits flush. Drive the screw in with a PZ2 Pozidriv bit held square to the work. The 60° thread and AB point form their own thread in the hole. These are not self-drilling, so test one screw in your material before fixing a whole run.
The zinc plating and powder coated head suit general exterior use; for constantly wet, marine or coastal sites choose a stainless steel screw. This product covers all 40 stocked RAL colours.
Loading delivery information...
Don't see your RAL colour listed above? Contact us to request a RAL Colour.