50mm x 4.8mm Coloured Countersunk Self-Tapping Screws - RAL Powder-Coated BZP Steel

(No reviews) Write a Review
Selected Step Two: Select Colour is
Screw Length: 50mm
Thread Size: 4.8mm
Material: BZP Steel
Head Type: Countersunk Head
Recess: Pozi PZ2
Thread Type: Self Tapping
colour_count: 40
tech_thread_type: Self Tapping
tech_head_style: Countersunk Head
tech_drive_type: Pozi PZ2
tech_length: 50mm
tech_diameter: 4.8mm
tech_material: BZP Steel
tech_coating: Premium powder coat
tech_colour_system: RAL Classic
  • Guaranteed Colour Match

    Matched to RAL Classic colours

  • In-House Experts

    We know our products

  • Durable Finish

    Dual layer powder coating

  • Same-Day Despatch*

    Order before 12pm

* Same-day despatch applies to stocked items only. Contact us if you need your order sooner than the stated lead time. Product images are for illustration only and should not be relied on as an accurate colour match – request a physical sample for an exact match.

50mm x 4.8mm Coloured Countersunk Self-Tapping Screws - RAL Powder-Coated BZP Steel
50mm x 4.8mm Coloured Countersunk Self-Tapping Screws - RAL Powder-Coated BZP Steel
£0.15

50mm x 4.8mm Coloured Countersunk Self-Tapping Screws - RAL Powder-Coated BZP Steel

£0.15

Description

Our multipurpose 50mm x 4.8mm painted countersunk self-tapping screws are used for stitching metal sheets together, attaching thin sheet metal to metal and general light fabrication. These colour-matched screws have a 60° self-tapping thread and a sharp AB point for easy insertion into a pre-drilled hole, while the countersunk head gives a discreet finish into pre-countersunk holes.

The carbon steel screw is plated in trivalent chromium (Cr3) zinc, then the head is powder coated to a RAL Classic colour so it matches the sheet around it instead of showing as a bright zinc dot. Drive it with a PZ2 Pozidriv bit, and make sure a pilot hole is drilled first, as these self-tapping screws are not self-drilling.

The 50mm fully threaded length reaches through lapped sheets, thicker stacks and deeper fixings, and is used by cladders, sign makers, hoarding installers and fabricators who want a clean, colour-matched finish.

40 RAL Colour-Matched Finishes

Each screw head is powder coated to a RAL Classic standard and oven cured. The finish gives a hard, uniform colour that stays consistent from one bag to the next, so a run of fixings across a sheet or panel looks even.

40 RAL colours are stocked for dispatch, covering whites, yellows, reds, purples, blues, greens, greys, browns and blacks. If your project calls for a colour outside the stocked set, contact us with your RAL reference for availability and lead times.

Site Applications

Where these 50mm x 4.8mm countersunk self-tapping screws are most often used:

  • Stitching metal sheets together
  • Attaching thin sheet metal to metal
  • Cladding, flashings and trims
  • Signage panels, frames and hoarding
  • Brackets and light fabrication through thicker stacks
  • Light timber fixings into a pre-drilled pilot hole

Specification

Specification at a glance:

Screw Type Self-tapping screw, countersunk head
Diameter 4.8mm (gauge 10 / No. 10)
Length 50mm (2 inch)
Imperial Size 10 x 2
Head Type Countersunk
Drive Pozidriv PZ2
Thread 60° self-tapping
Thread Coverage Fully threaded
Point AB point
Pre-Drilled Hole Required
Suitable Substrates Steel, thin sheet metal
Material Carbon steel
Plating Zinc plated, clear Cr3, before the heads are powder coated
Standard Manufactured to BS 4174:1972
Coating RAL Classic powder coated head
Colours Available 40 stocked RAL colours

Frequently Asked Questions

What are these self-tapping screws used for?

Stitching metal sheets together and attaching thin sheet metal to metal: cladding and flashing trims, signage panels and frames, hoarding, brackets and light fabrication. The 50mm length gives extra reach through lapped sheets and thicker stacks, and the countersunk head gives a discreet finish in a colour that matches the sheet.

Do I need to pre-drill a hole?

Yes. These are self-tapping, not self-drilling, so a pre-drilled hole is required. Drill a pilot hole slightly smaller than the 4.8mm thread, commonly around 4.0mm to 4.2mm in thin sheet steel, then drive the screw in and it forms its own thread. The right size depends on the material and its thickness, so test one screw first.

Does the countersunk head sink itself in?

No. The supplier designs the countersunk head to give a discreet finish into pre-countersunk holes, so the hole needs to be countersunk or dimpled first for the head to sit flush. If the head is left standing proud, the colour is still visible but the fixing will not be flush.

Should I choose the 38mm or the 50mm length?

Choose by what you are fixing. Add the thickness of every layer being joined, then pick the length that leaves the screw fully engaged in the final layer. The 50mm suits thicker stacks and deeper fixings; the 38mm suits thinner lapped sheets and trims. We stock the 38mm in the same 40 colours.

What is an AB point, and how is it different from a self-drilling screw?

The AB point is a sharp, tapered tip with a 60 degree self-tapping thread that cuts into a pre-drilled hole in thin sheet metal. A self-drilling (tek) screw has a drill tip and makes its own hole. If you want to drive straight into steel without drilling, choose one of our coloured self-drilling screws instead.

What driver bit do I need?

A PZ2 Pozidriv bit. Use a genuine PZ2 rather than a Phillips bit, which sits less securely in the recess and is more likely to cam out and mark the coloured head. Keep the driver square to the screw and use firm, even pressure.

What do 4.8mm, No. 10 and 10 x 2 mean?

They all describe the same screw. 4.8mm is the thread diameter (gauge 10, also written No. 10), and 50mm is the length, which is 2 inches. So a 10 x 2 and a 4.8 x 50 are the same size.

Can I use these outdoors?

For general exterior fixing the zinc plating and the powder coated head give protection. For constantly wet, marine or coastal locations, or where cut or drilled edges will be exposed, choose a stainless steel screw instead.

Can I choose a specific RAL colour?

Yes. 40 RAL Classic colours are stocked for dispatch, and the full list is shown on this page. If your project needs a colour outside the stocked set, contact us with your RAL reference for availability and lead times.

Powder Coated Self-Tapping Screws

Colour-matched fixings are all we do. Each screw head is finished to a RAL reference, so the colour you order is the colour you see on the head.

Electrostatically applied and heat cured, powder coating produces a harder, thicker and more durable finish than wet paint. On a fixing that is seen up close and expected to stay looking right, that difference is the whole point.

Benefits of powder coated self-tapping screws:

  • Scratch resistant
  • Rust resistant
  • UV resistant
  • Weather resistant
  • Colourfast

Available RAL Colours

These 50mm x 4.8mm coloured countersunk self-tapping screws are stocked in the following 40 RAL Classic colours. Select your colour from the options above, or view the full RALfixings colour guide for additional RAL colours available on request.

  • RAL 1013 Oyster White
  • RAL 1015 Light Ivory
  • RAL 1016 Sulphur Yellow
  • RAL 1019 Grey Beige
  • RAL 1020 Olive Yellow
  • RAL 1023 Traffic Yellow
  • RAL 1033 Dahlia Yellow
  • RAL 1036 Pearl Gold
  • RAL 3002 Carmine Red
  • RAL 3004 Purple Red
  • RAL 3009 Oxide Red
  • RAL 3020 Traffic Red
  • RAL 4006 Traffic Purple
  • RAL 4007 Violet Purple
  • RAL 4010 Telemagenta
  • RAL 5003 Sapphire Blue
  • RAL 5004 Black Blue
  • RAL 5012 Light Blue
  • RAL 5013 Cobalt Blue
  • RAL 5023 Distant Blue
  • RAL 5024 Pastel Blue
  • RAL 6003 Olive Green
  • RAL 6005 Moss Green
  • RAL 6012 Black Green
  • RAL 6016 Turquoise Green
  • RAL 6024 Traffic Green
  • RAL 6025 Fern Green
  • RAL 6027 Light Green
  • RAL 7009 Green Grey
  • RAL 7016 Anthracite Grey
  • RAL 7032 Pebble Grey
  • RAL 7035 Light Grey
  • RAL 7038 Agate Grey
  • RAL 7042 Traffic Grey A
  • RAL 8004 Copper Brown
  • RAL 8008 Olive Brown
  • RAL 8019 Grey Brown
  • RAL 9005 Jet Black
  • RAL 9010 Pure White
  • RAL 9016 Traffic White
tech_thread_type Self Tapping
tech_head_style Countersunk Head
tech_drive_type Pozi PZ2
tech_length 50mm
tech_diameter 4.8mm
tech_material BZP Steel
tech_coating Premium powder coat
tech_colour_system RAL Classic

Recommended applications

A colour-matched countersunk self-tapping screw for stitching metal sheets and fixing thin sheet metal to metal: cladding and flashing trims, signage panels and frames, hoarding, brackets and light fabrication. The 50mm length reaches through lapped sheets and thicker stacks, and the countersunk head gives a discreet finish in a RAL colour that matches the surface.

Drill a pilot hole first, commonly around 4.0mm to 4.2mm in thin sheet steel, and countersink or dimple it so the head sits flush. Drive the screw in with a PZ2 Pozidriv bit held square to the work. The 60° thread and AB point form their own thread in the hole. These are not self-drilling, so test one screw in your material before fixing a whole run.

The zinc plating and powder coated head suit general exterior use; for constantly wet, marine or coastal sites choose a stainless steel screw. This product covers all 40 stocked RAL colours.

Suitable for

Sheet Metal StitchingJoining lapped sheets and flashings with a colour-matched head
Cladding & TrimsFixing trims and edge details in a matching RAL colour
Signage & HoardingDiscreet countersunk fixings on panels and frames
Thicker Stacks50mm length reaches through layered sheet and brackets
Pre-Countersunk HolesHead sits flush when the hole is countersunk or dimpled

Loading delivery information...

Certificate of Conformity
ISO 9001 Approved
60+ RAL Colours
Fast UK Despatch

Don't see your RAL colour listed above? Contact us to request a RAL Colour.