M4 x 30mm Coloured Pan Head Machine Screws - RAL Powder-Coated BZP Steel

(No reviews) Write a Review
Selected Step Two: Select Colour is
Screw Length: 30mm
Thread Size: 4mm M4
Material: BZP Steel
Head Type: Pan Head
Recess: Pozi PZ2
Thread Type: Machine
colour_count: 40

  • Pan head for greater clamping
  • Free Pozidriv PZ2 driver bit included
  • Powder coated to any RAL Colour
  • UV & rust resistant
  • Guaranteed Colour Match

    Matched to RAL Classic colours

  • In-House Experts

    We know our products

  • Durable Finish

    Dual layer powder coating

  • Same-Day Despatch*

    Order before 12pm

* Same-day despatch applies to stocked items only. Contact us if you need your order sooner than the stated lead time. Product images are for illustration only and should not be relied on as an accurate colour match – request a physical sample for an exact match.

M4 x 30mm Coloured Pan Head Machine Screws - RAL Powder-Coated BZP Steel
M4 x 30mm Coloured Pan Head Machine Screws - RAL Powder-Coated BZP Steel
£0.13

M4 x 30mm Coloured Pan Head Machine Screws - RAL Powder-Coated BZP Steel

£0.13

Description

These M4 x 30mm coloured pan head machine screws give you a precise, removable metric fixing with the head finished in a RAL Classic colour of your choice. The carbon steel screw is bright zinc plated, fully threaded with a coarse M4 x 0.7 thread, and driven with a PZ2 Pozidriv bit. The powder coat means the screw matches the panel or housing around it instead of showing as a bright zinc dot.

As machine screws they are made for a tapped hole, a rivet nut, a threaded insert or an M4 nut, rather than cutting their own thread into raw metal or timber. The domed pan head spreads the clamping load over the surface and gives a clean, finished look on exposed fixings, and the 30mm length reaches through thicker panels, brackets and stacked layers.

They are used by sign makers, panel builders, fabricators and equipment manufacturers who want visible hardware to blend in or to be a deliberate colour accent.

40 RAL Colour-Matched Finishes

Each screw is powder coated to a RAL Classic standard and oven cured. The finish gives a hard, uniform colour that stays consistent from one bag to the next, so a run of fixings across a panel or enclosure looks even.

40 RAL colours are stocked for dispatch, covering whites, yellows, reds, purples, blues, greens, greys, browns and blacks. If your project calls for a colour outside the stocked set, contact us with your RAL reference for availability and lead times.

Site Applications

Where these M4 x 30mm pan head machine screws are most often used:

  • Electrical enclosures, control panels and equipment housings
  • Machinery covers, guards and brackets
  • Metal framing, shelving and furniture assemblies
  • Signage trays, fascia fixings and display fabrication
  • Appliance and equipment panels and trims
  • Joining thicker panels, brackets and stacked layers

Specification

Specification at a glance:

Screw Type Machine screw, pan head
Thread M4 (4mm) coarse metric, 0.7mm pitch
Length 30mm (measured under the head)
Thread Coverage Fully threaded
Head Type Pan
Drive Pozidriv PZ2
Material Carbon steel
Plating Bright zinc plated, clear Cr3 passivate
Standard DIN 7985
Tapped Hole Size 3.3mm drill, M4 x 0.7 tap
Clearance Hole Size 4.5mm (medium fit)
Coating RAL Classic powder coat
Colours Available 40 stocked RAL colours

Frequently Asked Questions

What are these machine screws used for?

Fixing parts together through a tapped hole or with an M4 nut: electrical enclosures and control panels, machinery covers and guards, metal framing and furniture, signage trays and fascias, and equipment housings. The extra length suits thicker panels, brackets and stacked layers, and the pan head sits proud of the surface so the RAL colour is part of the finished look.

Do I need a nut or a tapped hole?

Yes. These are machine screws with a uniform M4 x 0.7 metric thread, so they do not cut their own thread. Fasten them into a pre-tapped M4 hole, a rivet nut or threaded insert, or pass them through a clearance hole and secure with an M4 nut, ideally with a washer on soft or oversized holes.

What driver bit do I need?

A PZ2 Pozidriv bit. Use a genuine PZ2 rather than a Phillips bit, which sits less securely in the recess and is more likely to cam out and mark the coloured head. Keep the driver square to the screw and use firm, even pressure.

What length do I need?

The 30mm is measured from under the head to the tip. Add the thickness of the parts being joined, plus a nut and washer if you are using one, and allow a couple of threads to show past the nut. For a blind tapped hole, make sure the screw does not bottom out before the head clamps.

What hole size do I need?

For a tapped hole, drill 3.3mm and tap M4 x 0.7. For a clearance hole where the screw passes through a panel to a nut, drill 4.5mm (a medium fit that leaves room for the coating). Check the fit with one screw before drilling a whole run.

Should I choose pan head or countersunk?

Choose pan head when the screw is fixed to the face of a panel: the domed head spreads the clamping load and gives a clean, finished, colour-matched look. Choose countersunk where the head must sit flush, in a countersunk or dimpled hole. We also stock coloured countersunk machine screws in the same colour range.

Can I use these outdoors?

Yes, for general exterior fixing. The screw is carbon steel with a zinc plated base, and the powder coat adds a protective layer on top. For constantly wet, marine or coastal locations, or where cut or drilled edges will be exposed, choose a stainless steel screw instead.

Will the powder coat affect the thread fit?

Powder coating adds a thin layer to the screw, so a very tight tapped hole or nut may feel snug. Test one screw in your own hole or nut before fitting the full run, and drive the screw in square rather than forcing it.

Can I choose a specific RAL colour?

Yes. 40 RAL Classic colours are stocked for dispatch, and the full list is shown on this page. If your project needs a colour outside the stocked set, contact us with your RAL reference for availability and lead times.

Powder Coated Machine Screws

Colour-matched fixings are all we do. Each screw is finished to a RAL reference, so the colour you order is the colour on the screw.

Electrostatically applied and heat cured, powder coating produces a harder, thicker and more durable finish than wet paint. On a fixing that is seen up close and expected to stay looking right, that difference is the whole point.

Benefits of powder coated machine screws:

  • Scratch resistant
  • Rust resistant
  • UV resistant
  • Weather resistant
  • Colourfast

Available RAL Colours

These M4 x 30mm coloured pan head machine screws are stocked in the following 40 RAL Classic colours. Select your colour from the options above, or view the full RALfixings colour guide for additional RAL colours available on request.

  • RAL 1013 Oyster White
  • RAL 1015 Light Ivory
  • RAL 1016 Sulphur Yellow
  • RAL 1019 Grey Beige
  • RAL 1020 Olive Yellow
  • RAL 1023 Traffic Yellow
  • RAL 1033 Dahlia Yellow
  • RAL 1036 Pearl Gold
  • RAL 3002 Carmine Red
  • RAL 3004 Purple Red
  • RAL 3009 Oxide Red
  • RAL 3020 Traffic Red
  • RAL 4006 Traffic Purple
  • RAL 4007 Violet Purple
  • RAL 4010 Telemagenta
  • RAL 5003 Sapphire Blue
  • RAL 5004 Black Blue
  • RAL 5012 Light Blue
  • RAL 5013 Cobalt Blue
  • RAL 5023 Distant Blue
  • RAL 5024 Pastel Blue
  • RAL 6003 Olive Green
  • RAL 6005 Moss Green
  • RAL 6012 Black Green
  • RAL 6016 Turquoise Green
  • RAL 6024 Traffic Green
  • RAL 6025 Fern Green
  • RAL 6027 Light Green
  • RAL 7009 Green Grey
  • RAL 7016 Anthracite Grey
  • RAL 7032 Pebble Grey
  • RAL 7035 Light Grey
  • RAL 7038 Agate Grey
  • RAL 7042 Traffic Grey A
  • RAL 8004 Copper Brown
  • RAL 8008 Olive Brown
  • RAL 8019 Grey Brown
  • RAL 9005 Jet Black
  • RAL 9010 Pure White
  • RAL 9016 Traffic White

Recommended applications

A colour-matched M4 machine screw for fixing panels, covers and housings where the head is on show: electrical enclosures, control panels, machinery guards, metal framing, furniture and signage trays. The 30mm length suits thicker panels, brackets and stacked layers, with a domed pan head in a RAL colour that matches the surrounding surface.

Drill a 3.3mm hole and tap M4 x 0.7, or drill a 4.5mm clearance hole and fasten with an M4 nut and washer. Drive with a PZ2 Pozidriv bit held square to the screw, tightening firmly and evenly. These are machine screws, so they need a tapped hole, insert or nut and will not cut their own thread.

Test one screw in your own hole or nut first, as the powder coat adds a thin layer to the screw. The zinc plated steel body with powder coat suits general exterior use; for constantly wet, marine or coastal sites choose a stainless steel screw. This product covers all 40 stocked RAL colours.

Suitable for

Enclosures & Control PanelsCovers, lids and housings fixed to tapped holes or nuts
Signage Trays & FasciasColour-matched fixings on exposed sign hardware
Machinery & GuardsGuards, covers and brackets in a RAL colour scheme
Thicker Panels & Brackets30mm length reaches through stacked layers
Furniture & Metal FramingRemovable metric fixings with a finished look

Loading delivery information...

Certificate of Conformity
ISO 9001 Approved
60+ RAL Colours
Fast UK Despatch

Don't see your RAL colour listed above? Contact us to request a RAL Colour.