Coloured 16mm x 4.2mm Wafer Head Self Drilling Screws
These 16mm x 4.2mm wafer head self-drilling screws are the shortest stitching length in our wafer head range, made for joining drywall and ceiling track, thin sheet metal and light-gauge framing without a pilot hole. The drill-bit point cuts through steel up to 3.0mm thick and the Phillips PH2 recess drives with the bit already in every fixer’s kit.
The wafer head spreads the clamping load over a wide, flat bearing surface, which helps stop the screw pulling through thin material, and it sits low enough that boards, panels and trims can lie flush over it. At 16mm it gives enough thread engagement to hold light-gauge steel securely while leaving the least protrusion behind the track.
Powder coated to a RAL Classic colour of your choice, the head blends into the surface it is fixed to instead of showing up as a row of bright zinc dots. They suit dry-liners, metal framers, ductwork and M&E installers, signage and fit-out teams and fabricators.
40 RAL Colour-Matched Finishes
Each screw is powder coated to a RAL Classic standard and oven cured, giving a hard, uniform finish that resists scratching during installation and holds its colour once the job is finished. Unlike wet paint, it will not peel or chip when the screw is driven.
40 RAL colours are stocked for dispatch, covering whites, yellows, reds, purples, blues, greens, greys, browns and blacks. Whether you are matching RAL 9010 Pure White track, RAL 7016 Anthracite Grey trims or a brand colour, choose your shade from the options above. If you need a RAL outside the stocked set, contact us with your RAL reference for availability and lead times.
Matching the Screw to the Steel
The limit on this screw is steel thickness. The self-drilling point is rated for steel up to 3.0mm, which covers drywall track, stud and light-gauge framing. For thicker steel, choose a heavier self-drilling screw. For very thin gauge metal where you do not need a drill point, our sharp-point wafer head self-tapping screws are the alternative.
Common Applications
4.2 x 16mm coloured wafer head self-drilling screws are used wherever thin steel needs a flat, colour-matched fixing:
- Stitching drywall and ceiling track systems
- Joining metal stud to track before boarding
- Fixing overlapping sheet metal and ductwork
- Securing signage, brackets and panels to thin steel subframes
- Low-clearance fixings where a pan head would catch a board or panel
Specification
| Size (metric) | 4.2 x 16mm |
| Size (imperial) | 8 x 5/8″ |
| Head Type | Wafer (low profile) |
| Drive | Phillips PH2 |
| Point Type | Self-drilling |
| Thread Type | Self-tapping |
| Max Steel Thickness | 3.0mm (without pre-drilling) |
| Material | Carbon steel |
| Base Finish | Zinc plated (BZP) |
| Coating | RAL Classic powder coat |
| Substrates | Thin sheet metal, drywall track |
| Fire Classification | A1 (base screw) |
| Base Screw Standards | BS EN 14566:2008, BS EN 10666:2008 |
| Colours Available | 40 stocked RAL colours |
Frequently Asked Questions
What are 16mm x 4.2mm wafer head self drilling screws used for?
They are the shortest stitching length in the range, used for stitching drywall and ceiling track, joining metal stud to track, and fixing overlapping sheet metal and ductwork. The low-profile head sits flush and the 16mm length keeps the point from protruding far behind thin steel.
What is the maximum steel thickness?
Up to 3.0mm. The self-drilling point drills its own hole and the thread taps as it goes, so no pilot hole is needed. For thicker steel, step up to a heavier self-drilling screw such as a hex head tek screw.
Are they self-drilling or self-tapping?
Both. The drill-bit point cuts the hole and the self-tapping thread forms its own mating thread in the steel. That is different from our sharp-point wafer head self-tapping screws, which pierce only very thin gauge metal and have no drill flute.
When should I use 16mm rather than a longer wafer head?
Choose 16mm when you are stitching thin track or sheet that sits tight together and you want the shortest, flattest fixing that still bites securely. Step up to the 19mm, 22mm or 25mm lengths where layered materials, insulation or deeper sections put the steel further from the head.
What drive bit do I need?
A PH2 Phillips bit. Use a variable-speed driver, let the drill point do the work, and stop as soon as the head sits flat. Overdriving can strip the thread in thin gauge steel.
Can these be used in timber?
No. They are designed for steel and drywall track. For timber, use a wood screw or one of our wafer head self-tapping screws with a pilot hole where needed.
Can I choose a specific RAL colour?
Yes. 40 RAL colours are stocked for dispatch and each has its own product page. If you need a RAL outside the stocked set, contact us with the RAL reference for availability and lead times.
Powder Coated Screws
Colour-matched fixings are all we do. Each screw is finished to a RAL reference, so the colour you order is the colour on the screw. The powder is applied electrostatically and heat cured, which produces a harder, thicker and more durable finish than wet paint.
Benefits of powder coated screws:
- Scratch resistant
- Rust resistant
- UV resistant
- Weather resistant
- Colourfast
Available RAL Colours
These 16mm x 4.2mm coloured wafer head self-drilling screws are stocked in the following 40 RAL Classic colours. Select your colour from the options above, or view the full RALfixings colour guide for additional RAL colours available on request.
- RAL 1013 Oyster White
- RAL 1015 Light Ivory
- RAL 1016 Sulphur Yellow
- RAL 1019 Grey Beige
- RAL 1020 Olive Yellow
- RAL 1023 Traffic Yellow
- RAL 1033 Dahlia Yellow
- RAL 1036 Pearl Gold
- RAL 3002 Carmine Red
- RAL 3004 Purple Red
- RAL 3009 Oxide Red
- RAL 3020 Traffic Red
- RAL 4006 Traffic Purple
- RAL 4007 Violet Purple
- RAL 4010 Telemagenta
- RAL 5003 Sapphire Blue
- RAL 5004 Black Blue
- RAL 5012 Light Blue
- RAL 5013 Cobalt Blue
- RAL 5023 Distant Blue
- RAL 5024 Pastel Blue
- RAL 6003 Olive Green
- RAL 6005 Moss Green
- RAL 6012 Black Green
- RAL 6016 Turquoise Green
- RAL 6024 Traffic Green
- RAL 6025 Fern Green
- RAL 6027 Light Green
- RAL 7009 Green Grey
- RAL 7016 Anthracite Grey
- RAL 7032 Pebble Grey
- RAL 7035 Light Grey
- RAL 7038 Agate Grey
- RAL 7042 Traffic Grey A
- RAL 8004 Copper Brown
- RAL 8008 Olive Brown
- RAL 8019 Grey Brown
- RAL 9005 Jet Black
- RAL 9010 Pure White
- RAL 9016 Traffic White
Coloured 16mm x 4.2mm Wafer Head Self Drilling Screws
These 16mm x 4.2mm wafer head self-drilling screws are the shortest stitching length in our wafer head range, made for joining drywall and ceiling track, thin sheet metal and light-gauge framing without a pilot hole. The drill-bit point cuts through steel up to 3.0mm thick and the Phillips PH2 recess drives with the bit already in every fixer’s kit.
The wafer head spreads the clamping load over a wide, flat bearing surface, which helps stop the screw pulling through thin material, and it sits low enough that boards, panels and trims can lie flush over it. At 16mm it gives enough thread engagement to hold light-gauge steel securely while leaving the least protrusion behind the track.
Powder coated to a RAL Classic colour of your choice, the head blends into the surface it is fixed to instead of showing up as a row of bright zinc dots. They suit dry-liners, metal framers, ductwork and M&E installers, signage and fit-out teams and fabricators.
40 RAL Colour-Matched Finishes
Each screw is powder coated to a RAL Classic standard and oven cured, giving a hard, uniform finish that resists scratching during installation and holds its colour once the job is finished. Unlike wet paint, it will not peel or chip when the screw is driven.
40 RAL colours are stocked for dispatch, covering whites, yellows, reds, purples, blues, greens, greys, browns and blacks. Whether you are matching RAL 9010 Pure White track, RAL 7016 Anthracite Grey trims or a brand colour, choose your shade from the options above. If you need a RAL outside the stocked set, contact us with your RAL reference for availability and lead times.
Matching the Screw to the Steel
The limit on this screw is steel thickness. The self-drilling point is rated for steel up to 3.0mm, which covers drywall track, stud and light-gauge framing. For thicker steel, choose a heavier self-drilling screw. For very thin gauge metal where you do not need a drill point, our sharp-point wafer head self-tapping screws are the alternative.
Common Applications
4.2 x 16mm coloured wafer head self-drilling screws are used wherever thin steel needs a flat, colour-matched fixing:
- Stitching drywall and ceiling track systems
- Joining metal stud to track before boarding
- Fixing overlapping sheet metal and ductwork
- Securing signage, brackets and panels to thin steel subframes
- Low-clearance fixings where a pan head would catch a board or panel
Specification
| Size (metric) | 4.2 x 16mm |
| Size (imperial) | 8 x 5/8″ |
| Head Type | Wafer (low profile) |
| Drive | Phillips PH2 |
| Point Type | Self-drilling |
| Thread Type | Self-tapping |
| Max Steel Thickness | 3.0mm (without pre-drilling) |
| Material | Carbon steel |
| Base Finish | Zinc plated (BZP) |
| Coating | RAL Classic powder coat |
| Substrates | Thin sheet metal, drywall track |
| Fire Classification | A1 (base screw) |
| Base Screw Standards | BS EN 14566:2008, BS EN 10666:2008 |
| Colours Available | 40 stocked RAL colours |
Frequently Asked Questions
What are 16mm x 4.2mm wafer head self drilling screws used for?
They are the shortest stitching length in the range, used for stitching drywall and ceiling track, joining metal stud to track, and fixing overlapping sheet metal and ductwork. The low-profile head sits flush and the 16mm length keeps the point from protruding far behind thin steel.
What is the maximum steel thickness?
Up to 3.0mm. The self-drilling point drills its own hole and the thread taps as it goes, so no pilot hole is needed. For thicker steel, step up to a heavier self-drilling screw such as a hex head tek screw.
Are they self-drilling or self-tapping?
Both. The drill-bit point cuts the hole and the self-tapping thread forms its own mating thread in the steel. That is different from our sharp-point wafer head self-tapping screws, which pierce only very thin gauge metal and have no drill flute.
When should I use 16mm rather than a longer wafer head?
Choose 16mm when you are stitching thin track or sheet that sits tight together and you want the shortest, flattest fixing that still bites securely. Step up to the 19mm, 22mm or 25mm lengths where layered materials, insulation or deeper sections put the steel further from the head.
What drive bit do I need?
A PH2 Phillips bit. Use a variable-speed driver, let the drill point do the work, and stop as soon as the head sits flat. Overdriving can strip the thread in thin gauge steel.
Can these be used in timber?
No. They are designed for steel and drywall track. For timber, use a wood screw or one of our wafer head self-tapping screws with a pilot hole where needed.
Can I choose a specific RAL colour?
Yes. 40 RAL colours are stocked for dispatch and each has its own product page. If you need a RAL outside the stocked set, contact us with the RAL reference for availability and lead times.
Powder Coated Screws
Colour-matched fixings are all we do. Each screw is finished to a RAL reference, so the colour you order is the colour on the screw. The powder is applied electrostatically and heat cured, which produces a harder, thicker and more durable finish than wet paint.
Benefits of powder coated screws:
- Scratch resistant
- Rust resistant
- UV resistant
- Weather resistant
- Colourfast
Available RAL Colours
These 16mm x 4.2mm coloured wafer head self-drilling screws are stocked in the following 40 RAL Classic colours. Select your colour from the options above, or view the full RALfixings colour guide for additional RAL colours available on request.
- RAL 1013 Oyster White
- RAL 1015 Light Ivory
- RAL 1016 Sulphur Yellow
- RAL 1019 Grey Beige
- RAL 1020 Olive Yellow
- RAL 1023 Traffic Yellow
- RAL 1033 Dahlia Yellow
- RAL 1036 Pearl Gold
- RAL 3002 Carmine Red
- RAL 3004 Purple Red
- RAL 3009 Oxide Red
- RAL 3020 Traffic Red
- RAL 4006 Traffic Purple
- RAL 4007 Violet Purple
- RAL 4010 Telemagenta
- RAL 5003 Sapphire Blue
- RAL 5004 Black Blue
- RAL 5012 Light Blue
- RAL 5013 Cobalt Blue
- RAL 5023 Distant Blue
- RAL 5024 Pastel Blue
- RAL 6003 Olive Green
- RAL 6005 Moss Green
- RAL 6012 Black Green
- RAL 6016 Turquoise Green
- RAL 6024 Traffic Green
- RAL 6025 Fern Green
- RAL 6027 Light Green
- RAL 7009 Green Grey
- RAL 7016 Anthracite Grey
- RAL 7032 Pebble Grey
- RAL 7035 Light Grey
- RAL 7038 Agate Grey
- RAL 7042 Traffic Grey A
- RAL 8004 Copper Brown
- RAL 8008 Olive Brown
- RAL 8019 Grey Brown
- RAL 9005 Jet Black
- RAL 9010 Pure White
- RAL 9016 Traffic White
Delivery & Shipping Terms
1. Where We Deliver
We currently ship to addresses within the United Kingdom only.
If you require delivery outside the UK, this must be arranged in advance. Where international delivery is agreed:
- You are fully responsible for all import duties, taxes, and customs charges, including any fees for customs paperwork.
- RALfixings accepts no liability for customs delays or additional costs associated with international shipments.
2. Delivery Timescales
Our products fall into two categories: in-stock and made-to-order (bespoke) items.
In-Stock Items
- Usually dispatched within 1–2 working days.
- Delivery typically takes 1–3 working days from the dispatch date.
Powder Coated / Made-to-Order Items
- Typically dispatched within 3–5 working days, but may take up to 10 working days during busy periods.
- Delivery typically takes 1–3 working days after dispatch.
All quoted times are estimates, not guarantees. Delivery times may be affected by stock availability, courier performance, weather, or other factors beyond our control.
3. Shipping Costs
- Shipping charges are based on order weight and destination.
- The exact shipping cost will be shown at checkout before payment.
- Additional shipping charges may apply to remote areas or multiple consignments.
4. Tracking and Responsibility
All orders are shipped via tracked courier services to ensure maximum security and visibility.
Once your order has been dispatched:
- You will receive an order dispatch email letting you know your order is on it's way, and another email from Royal Mail or the chosen courier with your tracking information. If you have supplied a UK phone number you may also recieve a tracking text from Royal Mail or the chosen courier.
- Responsibility for the goods passes to you upon dispatch.
- RALfixings is not liable for loss or damage in transit. Please contact the courier directly with your tracking number if issues arise.
5. Missed Deliveries or Delays
If your parcel cannot be delivered and is returned to us:
- We can resend it, but an additional delivery charge will apply.
- We are not responsible for courier delays or failed delivery attempts.
If your order hasn’t arrived within the estimated delivery window, please contact us as soon as possible at info@ralfixings.com.
Order Amendments & Cancellations
Changing an Order
We begin preparing orders quickly — especially made-to-order items.
- If you need to amend your order, please contact us within 24 hours or as soon as possible.
- After this period, it may be too late to make changes as your order may already be in production or dispatched.
- If you wish to add items, and your order hasn’t yet shipped, we may be able to combine them. Otherwise, a new order (and delivery charge) will apply.
Returns & Refunds
1. Your Right to Cancel – B2C Customers Only
Under the Consumer Contracts Regulations 2013, B2C customers have the right to cancel certain purchases made online within 14 days of delivery.
However, this does not apply to:
- Bespoke or made-to-order goods — including all powder coated screws and fixings manufactured specifically for your order.
If your order includes stocked items only, you may cancel and return those goods within 14 days of receipt. You must:
- Inform us in writing via email within 14 days.
- Return the goods at your own cost, in their original condition and packaging.
- Ensure the items are received by us within 30 days of delivery.
We recommend using a tracked and insured delivery service for any returns, as we are not responsible for items lost or damaged in return transit.
2. Faulty or Incorrect Items
If you receive goods that are:
- Faulty, or
- Incorrectly supplied (e.g. wrong size, colour, or product)
Please notify us within 30 days of receiving the goods.
We will:
- Replace the items where possible, or
- Issue a refund if replacement is not appropriate.
You may be asked to return the faulty items for inspection before a refund or exchange is processed.
Once screws have been installed or used, they cannot be returned or refunded, unless faulty.
3. Refund Processing
- Refunds (where applicable) are processed within 5 working days of receiving the returned items.
- Refunds are only issued to the original payment method.
- Refunds cannot be made to a different card or by other means.
- Delivery charges are non-refundable unless your entire order was cancelled before dispatch or the goods were faulty or incorrect.
Returns Address
To return items, please send them to:
FAO: Jon Lett
RALfixings Ltd
26a Queens Road
Knaphill
Surrey
GU212DX
B2B Orders & Restocking Fee
The rights described above apply primarily to consumers (B2C). If you are a business customer (B2B), statutory cancellation rights under the Consumer Contracts Regulations do not apply.
Returns from business customers are accepted at our sole discretion, and only if agreed in writing before the goods are returned.
All authorised B2B returns are subject to a 15% restocking fee, which will be deducted from the final refund amount. This fee covers the cost of inspection, repackaging, and administrative processing.
Returned goods must be:
- In resaleable, unused condition
- In their original packaging
- Returned at the buyer’s expense via a tracked delivery service
We do not accept returns of any bespoke or made-to-order products under any circumstances unless the item is faulty.
What our customers say
Posted by Demetri on 18th Dec 2024
Exactly as ordered and does exactly what they're supposed to.
SIMPLE TEST - CAN YOU SEE THIS?
If you see this, the partial is loading.
Coloured 16mm x 4.2mm Wafer Head Self Drilling Screws
These 16mm x 4.2mm wafer head self-drilling screws are the shortest stitching length in our wafer head range, made for joining drywall and ceiling track, thin sheet metal and light-gauge framing without a pilot hole. The drill-bit point cuts through steel up to 3.0mm thick and the Phillips PH2 recess drives with the bit already in every fixer’s kit.
The wafer head spreads the clamping load over a wide, flat bearing surface, which helps stop the screw pulling through thin material, and it sits low enough that boards, panels and trims can lie flush over it. At 16mm it gives enough thread engagement to hold light-gauge steel securely while leaving the least protrusion behind the track.
Powder coated to a RAL Classic colour of your choice, the head blends into the surface it is fixed to instead of showing up as a row of bright zinc dots. They suit dry-liners, metal framers, ductwork and M&E installers, signage and fit-out teams and fabricators.
40 RAL Colour-Matched Finishes
Each screw is powder coated to a RAL Classic standard and oven cured, giving a hard, uniform finish that resists scratching during installation and holds its colour once the job is finished. Unlike wet paint, it will not peel or chip when the screw is driven.
40 RAL colours are stocked for dispatch, covering whites, yellows, reds, purples, blues, greens, greys, browns and blacks. Whether you are matching RAL 9010 Pure White track, RAL 7016 Anthracite Grey trims or a brand colour, choose your shade from the options above. If you need a RAL outside the stocked set, contact us with your RAL reference for availability and lead times.
Matching the Screw to the Steel
The limit on this screw is steel thickness. The self-drilling point is rated for steel up to 3.0mm, which covers drywall track, stud and light-gauge framing. For thicker steel, choose a heavier self-drilling screw. For very thin gauge metal where you do not need a drill point, our sharp-point wafer head self-tapping screws are the alternative.
Common Applications
4.2 x 16mm coloured wafer head self-drilling screws are used wherever thin steel needs a flat, colour-matched fixing:
- Stitching drywall and ceiling track systems
- Joining metal stud to track before boarding
- Fixing overlapping sheet metal and ductwork
- Securing signage, brackets and panels to thin steel subframes
- Low-clearance fixings where a pan head would catch a board or panel
Specification
| Size (metric) | 4.2 x 16mm |
| Size (imperial) | 8 x 5/8″ |
| Head Type | Wafer (low profile) |
| Drive | Phillips PH2 |
| Point Type | Self-drilling |
| Thread Type | Self-tapping |
| Max Steel Thickness | 3.0mm (without pre-drilling) |
| Material | Carbon steel |
| Base Finish | Zinc plated (BZP) |
| Coating | RAL Classic powder coat |
| Substrates | Thin sheet metal, drywall track |
| Fire Classification | A1 (base screw) |
| Base Screw Standards | BS EN 14566:2008, BS EN 10666:2008 |
| Colours Available | 40 stocked RAL colours |
Frequently Asked Questions
What are 16mm x 4.2mm wafer head self drilling screws used for?
They are the shortest stitching length in the range, used for stitching drywall and ceiling track, joining metal stud to track, and fixing overlapping sheet metal and ductwork. The low-profile head sits flush and the 16mm length keeps the point from protruding far behind thin steel.
What is the maximum steel thickness?
Up to 3.0mm. The self-drilling point drills its own hole and the thread taps as it goes, so no pilot hole is needed. For thicker steel, step up to a heavier self-drilling screw such as a hex head tek screw.
Are they self-drilling or self-tapping?
Both. The drill-bit point cuts the hole and the self-tapping thread forms its own mating thread in the steel. That is different from our sharp-point wafer head self-tapping screws, which pierce only very thin gauge metal and have no drill flute.
When should I use 16mm rather than a longer wafer head?
Choose 16mm when you are stitching thin track or sheet that sits tight together and you want the shortest, flattest fixing that still bites securely. Step up to the 19mm, 22mm or 25mm lengths where layered materials, insulation or deeper sections put the steel further from the head.
What drive bit do I need?
A PH2 Phillips bit. Use a variable-speed driver, let the drill point do the work, and stop as soon as the head sits flat. Overdriving can strip the thread in thin gauge steel.
Can these be used in timber?
No. They are designed for steel and drywall track. For timber, use a wood screw or one of our wafer head self-tapping screws with a pilot hole where needed.
Can I choose a specific RAL colour?
Yes. 40 RAL colours are stocked for dispatch and each has its own product page. If you need a RAL outside the stocked set, contact us with the RAL reference for availability and lead times.
Powder Coated Screws
Colour-matched fixings are all we do. Each screw is finished to a RAL reference, so the colour you order is the colour on the screw. The powder is applied electrostatically and heat cured, which produces a harder, thicker and more durable finish than wet paint.
Benefits of powder coated screws:
- Scratch resistant
- Rust resistant
- UV resistant
- Weather resistant
- Colourfast
Available RAL Colours
These 16mm x 4.2mm coloured wafer head self-drilling screws are stocked in the following 40 RAL Classic colours. Select your colour from the options above, or view the full RALfixings colour guide for additional RAL colours available on request.
- RAL 1013 Oyster White
- RAL 1015 Light Ivory
- RAL 1016 Sulphur Yellow
- RAL 1019 Grey Beige
- RAL 1020 Olive Yellow
- RAL 1023 Traffic Yellow
- RAL 1033 Dahlia Yellow
- RAL 1036 Pearl Gold
- RAL 3002 Carmine Red
- RAL 3004 Purple Red
- RAL 3009 Oxide Red
- RAL 3020 Traffic Red
- RAL 4006 Traffic Purple
- RAL 4007 Violet Purple
- RAL 4010 Telemagenta
- RAL 5003 Sapphire Blue
- RAL 5004 Black Blue
- RAL 5012 Light Blue
- RAL 5013 Cobalt Blue
- RAL 5023 Distant Blue
- RAL 5024 Pastel Blue
- RAL 6003 Olive Green
- RAL 6005 Moss Green
- RAL 6012 Black Green
- RAL 6016 Turquoise Green
- RAL 6024 Traffic Green
- RAL 6025 Fern Green
- RAL 6027 Light Green
- RAL 7009 Green Grey
- RAL 7016 Anthracite Grey
- RAL 7032 Pebble Grey
- RAL 7035 Light Grey
- RAL 7038 Agate Grey
- RAL 7042 Traffic Grey A
- RAL 8004 Copper Brown
- RAL 8008 Olive Brown
- RAL 8019 Grey Brown
- RAL 9005 Jet Black
- RAL 9010 Pure White
- RAL 9016 Traffic White
Recommended applications
Engineered for stitching light-gauge metal framing systems and fixing thin sheet metal without pre-drilling. The self-drilling point cuts its own hole through steel up to 3.0mm, while the wide, low-profile wafer head spreads clamping load and sits flush so it will not foul boards, panels or moving parts fitted over it.
Widely used by drylining and partition contractors for joining metal stud to track before boarding, and by signage and fit-out teams fixing panels directly to steel subframes. Drive with a variable-speed driver and a PH2 bit; let the drill point do the work and avoid overdriving, which can strip the thread in thin gauge steel.
For fixing into timber or pre-drilled substrates where a drill point is not required, see the wafer head self-tapping range. This product covers all 40 stocked RAL colours.
Suitable for
In Stock
| Bulk Discount | ||
|---|---|---|
| 200+ | ||
| 500+ | ||
| 1000+ | ||
| 2000+ | ||
| 5000+ | ||