50mm x 4.2mm Coloured Pan Head Self-Tapping Screws - RAL Powder-Coated BZP Steel

(No reviews) Write a Review
Selected Step Two: Select Colour is
Screw Length: 50mm
Thread Size: 4.2mm
Material: BZP Steel
Head Type: Pan Head
Recess: Pozi PZ2
Thread Type: Self Tapping
tech_thread_type: Self Tapping (ST)
tech_head_style: Pan Head
tech_drive_type: Pozidrive PZ2
tech_length: 50mm
tech_diameter: 4.2mm
tech_material: BZP Steel
tech_coating: Premium powder coat
tech_colour_system: RAL Classic
colour_count: 40

  • Ideal for wood & thin sheet metal
  • Pan head for increased clamping
  • Powder coated to any RAL Colour
  • UV & rust resistant
  • Free Pozidrive PZ2 driver bit included
  • Guaranteed Colour Match

    Matched to RAL Classic colours

  • In-House Experts

    We know our products

  • Durable Finish

    Dual layer powder coating

  • Same-Day Despatch*

    Order before 12pm

* Same-day despatch applies to stocked items only. Contact us if you need your order sooner than the stated lead time. Product images are for illustration only and should not be relied on as an accurate colour match – request a physical sample for an exact match.

50mm x 4.2mm Coloured Pan Head Self-Tapping Screws - RAL Powder-Coated BZP Steel
50mm x 4.2mm Coloured Pan Head Self-Tapping Screws - RAL Powder-Coated BZP Steel
£0.14

50mm x 4.2mm Coloured Pan Head Self-Tapping Screws - RAL Powder-Coated BZP Steel

£0.14

Description

Our multipurpose 50mm x 4.2mm painted pan head self-tapping screws are used for stitching metal sheets together, attaching thin sheet metal to metal and general light fabrication. These colour-matched screws have a 60° self-tapping thread and a sharp AB point for easy insertion into a pre-drilled hole, while the pan head gives extra clamping.

The carbon steel screw is plated in trivalent chromium (Cr3) zinc before it is powder coated to a RAL Classic colour, so the head matches the sheet around it instead of showing as a bright zinc dot. Drive it with a PZ2 Pozidriv bit, and make sure a pilot hole is drilled first, as these self-tapping screws are not self-drilling.

At 50mm long they reach through thicker stacks, flashings and lapped sheets, and are used by roofers, cladders, sign makers and fabricators who want a clean, colour-matched finish.

40 RAL Colour-Matched Finishes

Each screw is powder coated to a RAL Classic standard and oven cured. The finish gives a hard, uniform colour that stays consistent from one bag to the next, so a run of fixings across a sheet or panel looks even.

40 RAL colours are stocked for dispatch, covering whites, yellows, reds, purples, blues, greens, greys, browns and blacks. If your project calls for a colour outside the stocked set, contact us with your RAL reference for availability and lead times.

Site Applications

Where these 50mm x 4.2mm pan head self-tapping screws are most often used:

  • Stitching metal sheets together
  • Attaching thin sheet metal to metal
  • Cladding, flashings and trims
  • Ducting, enclosures and brackets
  • Signage plates and fascia fixings
  • Light timber fixings into a pre-drilled pilot hole

Specification

Specification at a glance:

Screw Type Self-tapping screw, pan head
Diameter 4.2mm (gauge 8 / No. 8)
Length 50mm (2 inch)
Imperial Size 8 x 2
Head Type Pan
Drive Pozidriv PZ2
Thread 60° self-tapping
Point AB point
Pre-Drilled Hole Required
Suitable Substrates Steel, thin sheet metal
Material Carbon steel
Plating Zinc plated, trivalent chromium (Cr3), clear
Standard Manufactured to BS 4174:1972
Coating RAL Classic powder coat
Colours Available 40 stocked RAL colours

Frequently Asked Questions

What are these self-tapping screws used for?

Stitching metal sheets together and attaching thin sheet metal to metal: cladding and flashing trims, ducting, enclosures, brackets, signage plates and light fabrication. The pan head gives extra clamping, and the RAL powder coat matches the screw to the sheet so the fixing blends in.

Do I need to pre-drill a hole?

Yes. These are self-tapping, not self-drilling, so a pre-drilled hole is required. Drill a pilot hole slightly smaller than the 4.2mm thread, commonly around 3.3mm to 3.5mm in thin sheet steel, then drive the screw in and it forms its own thread. The right size depends on the material and its thickness, so test one screw first.

What is an AB point, and how is it different from a self-drilling screw?

The AB point is a sharp, tapered tip with a 60 degree self-tapping thread that cuts into a pre-drilled hole in thin sheet metal. A self-drilling (tek) screw has a drill tip and makes its own hole. If you want to drive straight into steel without drilling, choose one of our coloured self-drilling screws instead.

What driver bit do I need?

A PZ2 Pozidriv bit. Use a genuine PZ2 rather than a Phillips bit, which sits less securely in the recess and is more likely to cam out and mark the coloured head. Keep the driver square to the screw and use firm, even pressure.

What do 4.2mm, No. 8 and 8 x 2 mean?

They all describe the same screw. 4.2mm is the thread diameter (gauge 8, also written No. 8), and 50mm is the length, which is 2 inches. So an 8 x 2 and a 4.2 x 50 are the same size, and this is that screw with a powder coated head.

Can I use these in wood?

They are designed for thin sheet metal and metal-to-metal fixing. In light timber they can hold small fixings into a pre-drilled pilot hole, but for structural or load-bearing timber use a proper wood screw.

Can I use these outdoors?

Yes, for general exterior fixing. The screw is carbon steel with trivalent chromium (Cr3) zinc plating, and the powder coat adds a protective layer on top. For constantly wet, marine or coastal locations, or where cut or drilled edges will be exposed, choose a stainless steel screw instead.

Can I choose a specific RAL colour?

Yes. 40 RAL Classic colours are stocked for dispatch, and the full list is shown on this page. If your project needs a colour outside the stocked set, contact us with your RAL reference for availability and lead times.

Powder Coated Self-Tapping Screws

Colour-matched fixings are all we do. Each screw is finished to a RAL reference, so the colour you order is the colour on the screw.

Electrostatically applied and heat cured, powder coating produces a harder, thicker and more durable finish than wet paint. On a fixing that is seen up close and expected to stay looking right, that difference is the whole point.

Benefits of powder coated self-tapping screws:

  • Scratch resistant
  • Rust resistant
  • UV resistant
  • Weather resistant
  • Colourfast

Available RAL Colours

These 50mm x 4.2mm coloured pan head self-tapping screws are stocked in the following 40 RAL Classic colours. Select your colour from the options above, or view the full RALfixings colour guide for additional RAL colours available on request.

  • RAL 1013 Oyster White
  • RAL 1015 Light Ivory
  • RAL 1016 Sulphur Yellow
  • RAL 1019 Grey Beige
  • RAL 1020 Olive Yellow
  • RAL 1023 Traffic Yellow
  • RAL 1033 Dahlia Yellow
  • RAL 1036 Pearl Gold
  • RAL 3002 Carmine Red
  • RAL 3004 Purple Red
  • RAL 3009 Oxide Red
  • RAL 3020 Traffic Red
  • RAL 4006 Traffic Purple
  • RAL 4007 Violet Purple
  • RAL 4010 Telemagenta
  • RAL 5003 Sapphire Blue
  • RAL 5004 Black Blue
  • RAL 5012 Light Blue
  • RAL 5013 Cobalt Blue
  • RAL 5023 Distant Blue
  • RAL 5024 Pastel Blue
  • RAL 6003 Olive Green
  • RAL 6005 Moss Green
  • RAL 6012 Black Green
  • RAL 6016 Turquoise Green
  • RAL 6024 Traffic Green
  • RAL 6025 Fern Green
  • RAL 6027 Light Green
  • RAL 7009 Green Grey
  • RAL 7016 Anthracite Grey
  • RAL 7032 Pebble Grey
  • RAL 7035 Light Grey
  • RAL 7038 Agate Grey
  • RAL 7042 Traffic Grey A
  • RAL 8004 Copper Brown
  • RAL 8008 Olive Brown
  • RAL 8019 Grey Brown
  • RAL 9005 Jet Black
  • RAL 9010 Pure White
  • RAL 9016 Traffic White
tech_thread_type Self Tapping (ST)
tech_head_style Pan Head
tech_drive_type Pozidrive PZ2
tech_length 50mm
tech_diameter 4.2mm
tech_material BZP Steel
tech_coating Premium powder coat
tech_colour_system RAL Classic

Recommended applications

A colour-matched pan head self-tapping screw for stitching metal sheets and fixing thin sheet metal to metal: cladding and flashing trims, ducting, enclosures, brackets and signage plates. The 50mm length reaches through lapped sheets and thicker stacks, and the pan head clamps firmly while showing a clean RAL colour.

Drill a pilot hole first, commonly around 3.3mm to 3.5mm in thin sheet steel, then drive the screw in with a PZ2 Pozidriv bit held square to the work. The 60° thread and AB point form their own thread in the hole. These are not self-drilling, so test one screw in your material before fixing a whole run.

The zinc plated steel body with powder coat suits general exterior use; for constantly wet, marine or coastal sites choose a stainless steel screw. This product covers all 40 stocked RAL colours.

Suitable for

Sheet Metal StitchingJoining lapped sheets and flashings with a colour-matched head
Cladding & TrimsFixing trims and edge details in a matching RAL colour
Signage Plates & FasciasClean, domed fixings on exposed sign hardware
Ducting & EnclosuresBrackets, covers and light fabrication in thin sheet
Thicker Stacks50mm length reaches through layered materials

Loading delivery information...

Certificate of Conformity
ISO 9001 Approved
60+ RAL Colours
Fast UK Despatch

Don't see your RAL colour listed above? Contact us to request a RAL Colour.