Write a Review
RoofingPro RS70 Roofing Screws - 70mm - RAL 9010 Pure White
Description
The RoofingPro™ RS70 is a 70mm x 5.5mm hex head self-drilling roofing screw finished in RAL 9010 Pure White. It fixes profiled metal roofing and wall cladding sheets directly to light section steel without a pilot hole, and it does it in a colour that disappears against the sheet rather than sitting on top of it.
Built for roofing contractors, cladding installers and steel-frame fabricators working on commercial, industrial and agricultural envelopes. The No.3 self-drilling point cuts through steel up to 5mm thick, so purlins, rails and sheeting rails are all within range from a single fixing.
At 70mm it is the long-reach option, made for deep profiles, spacer bars and insulated build-ups where the fixing has to pass through a thick construction before it ever reaches the steel. The 55mm of effective thread engages behind the sheet to pull it tight to the steel.
Both the hex head and the EPDM sealing washer are powder coated in RAL 9010. Most coloured roofing screws stop at the head and leave a black rubber washer showing beneath it. This one does not.
Colour Matched in RAL 9010 Pure White
Pure white is the standard interior and soffit finish across insulated panel systems, and appears widely on food production units, cold stores, warehousing and light industrial envelopes where a clean, bright surface is required.
RAL 9010 is a soft slightly warm white, and the RS70 carries it across the full hex head and the bonded EPDM washer beneath. RAL 9010 is the white specified when a warmer, softer tone is wanted rather than a stark commercial white. It is regularly paired with grey or silver profiles as the underside and trim colour.
Colour matching the fixing is not cosmetic detailing. On a roof or elevation that carries several hundred visible screws, an unmatched head is the detail a client notices from the car park and a specifier notices at handover.
Held in stock for rapid dispatch alongside the rest of the core RoofingPro palette.
Site Applications
Where the RS70 is most often used on site:
- Deep box and trapezoidal roof profiles onto steel purlins
- Insulated panel and composite sheet fixing where the build-up is thick
- Spacer bar and standoff systems onto light section steel
- Over-roofing and re-sheeting onto existing profiled decks
- Cladding fixing through insulation onto steel rails
Typical fixing centres: 300mm - 500mm at sheet ends and 500mm - 1000mm at intermediate purlins (subject to sheet profile and wind loading).
Specification
Specification at a glance:
| Size | 5.5mm x 70mm |
| Head Type | Hex |
| Socket Size | 8mm |
| Point Type | Self-Drilling No.3 |
| Thread Type | 60° Self-Tapping |
| Effective Thread Length | 55mm |
| EPDM Washer | 16mm |
| FW Ø | 11mm |
| Max Drilling Thickness | 5mm |
| Material | Case & Core Hardened Carbon Steel |
| Substrate | Steel |
| Shank Finish | Bright Zinc Plated |
| Head & Washer Finish | Powder Coated |
| Colour | RAL 9010 Pure White |
Frequently Asked Questions
What are these screws for?
Fixing profiled metal roofing and wall cladding sheets to light section steel framing without pre-drilling, in a finish that matches the sheet.
Are the head and washer the same colour?
Yes, both are powder coated in RAL 9010 Pure White. Coating the EPDM washer as well as the head is what separates the RoofingPro range from a standard coloured tek screw.
What steel thickness can they handle?
Up to 5mm. Beyond that a higher-rated drill point or a pre-drilled hole is required.
Can I order a small quantity?
Yes. The range is sold by the unit, so you can order exactly what a job needs. Quantity breaks start at 200 screws.
Powder Coated Roofing Screws
Colour-matched fixings are all we do. Powder coating in-house means the RAL reference on the box is the RAL reference on the screw, and it means we can carry the finish across both the hex head and the sealing washer.
Electrostatically applied and heat cured, powder coating produces a harder, thicker and more durable finish than wet paint. On a roof fixing exposed to standing water, UV and thermal cycling for decades, that difference is the whole point.
Benefits of powder coated roofing screws:
- Scratch resistant
- Rust resistant
- UV resistant
- Weather resistant
- Colourfast
Other RoofingPro RS70 Colour Options
RoofingPro™ RS70 roofing screws are stocked in six core RAL finishes matched to the most widely specified roofing and cladding colours, with further RAL references powder coated to order.
| tech_thread_type | Self Drilling (SD) |
|---|---|
| tech_head_style | Hex Head |
| tech_drive_type | 5/16 Hex Socket (8mm) |
| tech_length | 70mm |
| tech_diameter | 5.5mm |
| tech_gauge | No. 12 |
| tech_point_type | Self-Drilling No.3 |
| tech_steel_capacity | Up to 5mm total (Max Drilling Thickness) |
| tech_material | BZP Steel |
| tech_coating | Premium powder coat |
| tech_ral_code | RAL 9010 |
| tech_ral_name | Pure White |
| tech_colour_system | RAL Classic |
Recommended applications
Engineered for fixing profiled metal roofing and wall cladding sheets to light section steel framing on commercial, industrial and agricultural buildings. The 70mm length clears deep profiles and insulated build-ups before landing in the steel. The powder coated hex head and colour-matched EPDM washer keep fixings visually consistent with the sheet across an entire elevation.
The No.3 self-drilling point cuts through steel up to 5mm without a pilot hole. Drive with an 8mm socket in a variable-speed driver and stop as soon as the washer compresses evenly. Overdriving crushes the EPDM and destroys the seal.
Not suitable for fixing into timber — the self-drilling point is designed for steel substrates. For timber framing see our self-tapping wafer head range.
Suitable for
Loading delivery information...