Write a Review
RoofingPro RS50 Roofing Screws - 50mm - RAL 7016 Anthracite Grey
Description
The RoofingPro™ RS50 is a 50mm x 5.5mm hex head self-drilling roofing screw finished in RAL 7016 Anthracite Grey. It fixes profiled metal roofing and wall cladding sheets directly to light section steel without a pilot hole, and it does it in a colour that disappears against the sheet rather than sitting on top of it.
Built for roofing contractors, cladding installers and steel-frame fabricators working on commercial, industrial and agricultural envelopes. The No.3 self-drilling point cuts through steel up to 5mm thick, so purlins, rails and sheeting rails are all within range from a single fixing.
Where this screw earns its place is on visible elevations. A roof sheet or cladding panel is only as finished as the several hundred fixings holding it down, and a bright zinc head against a coloured sheet is the first thing the eye lands on.
Both the hex head and the EPDM sealing washer are powder coated in RAL 7016. Most coloured roofing screws stop at the head and leave a black rubber washer showing beneath it. This one does not.
Colour Matched in RAL 7016 Anthracite Grey
Anthracite grey is the default specification for modern commercial architecture. It appears on standing seam roofs, rainscreen cassettes, curtain walling, window systems and insulated panel envelopes across almost every new-build scheme in the UK.
RAL 7016 is a deep blue-toned charcoal, and the RS50 carries it across the full hex head and the bonded EPDM washer beneath. Because RAL 7016 dominates the cladding and fenestration market, it is the colour most often left unmatched at the fixing. A bright zinc head against an anthracite roof sheet is the detail that betrays a rushed installation.
Colour matching the fixing is not cosmetic detailing. On a roof or elevation that carries several hundred visible screws, an unmatched head is the detail a client notices from the car park and a specifier notices at handover.
Held in stock for rapid dispatch alongside the rest of the core RoofingPro palette.
Site Applications
Where the RS50 is most often used on site:
- Metal roofing sheet to steel purlin fixing, up to 5mm steel thickness
- Rainscreen and cladding panel fixing onto steel subframes
- Farm buildings, grain stores and livestock housing roof sheeting
- Fascia, soffit and trim fixing on metal-clad commercial units
- Overlap and side-lap fixing on profiled sheet systems
Typical fixing centres: 300mm - 500mm at sheet ends and 500mm - 1000mm at intermediate purlins (subject to sheet profile and wind loading).
Specification
Specification at a glance:
| Size | 5.5mm x 50mm |
| Head Type | Hex |
| Socket Size | 8mm |
| Point Type | Self-Drilling No.3 |
| Thread Type | 60° Self-Tapping |
| Effective Thread Length | 35mm |
| EPDM Washer | 16mm |
| FW Ø | 11mm |
| Max Drilling Thickness | 5mm |
| Material | Case & Core Hardened Carbon Steel |
| Substrate | Steel |
| Shank Finish | Bright Zinc Plated |
| Head & Washer Finish | Powder Coated |
| Colour | RAL 7016 Anthracite Grey |
Frequently Asked Questions
What are these screws for?
Fixing profiled metal roofing and wall cladding sheets to light section steel framing without pre-drilling, in a finish that matches the sheet.
Are the head and washer the same colour?
Yes, both are powder coated in RAL 7016 Anthracite Grey. Coating the EPDM washer as well as the head is what separates the RoofingPro range from a standard coloured tek screw.
What steel thickness can they handle?
Up to 5mm. Beyond that a higher-rated drill point or a pre-drilled hole is required.
Can I order a small quantity?
Yes. The range is sold by the unit, so you can order exactly what a job needs. Quantity breaks start at 200 screws.
Powder Coated Roofing Screws
Colour-matched fixings are all we do. Powder coating in-house means the RAL reference on the box is the RAL reference on the screw, and it means we can carry the finish across both the hex head and the sealing washer.
Electrostatically applied and heat cured, powder coating produces a harder, thicker and more durable finish than wet paint. On a roof fixing exposed to standing water, UV and thermal cycling for decades, that difference is the whole point.
Benefits of powder coated roofing screws:
- Scratch resistant
- Rust resistant
- UV resistant
- Weather resistant
- Colourfast
Other RoofingPro RS50 Colour Options
RoofingPro™ RS50 roofing screws are stocked in six core RAL finishes matched to the most widely specified roofing and cladding colours, with further RAL references powder coated to order.
| tech_thread_type | Self Drilling (SD) |
|---|---|
| tech_head_style | Hex Head |
| tech_drive_type | 5/16 Hex Socket (8mm) |
| tech_length | 50mm |
| tech_diameter | 5.5mm |
| tech_gauge | No. 12 |
| tech_point_type | Self-Drilling No.3 |
| tech_steel_capacity | Up to 5mm total (Max Drilling Thickness) |
| tech_material | BZP Steel |
| tech_coating | Premium powder coat |
| tech_ral_code | RAL 7016 |
| tech_ral_name | Anthracite Grey |
| tech_colour_system | RAL Classic |
Recommended applications
Engineered for fixing profiled metal roofing and wall cladding sheets to light section steel framing on commercial, industrial and agricultural buildings. The powder coated hex head and colour-matched EPDM washer keep fixings visually consistent with the sheet across an entire elevation.
The No.3 self-drilling point cuts through steel up to 5mm without a pilot hole. Drive with an 8mm socket in a variable-speed driver and stop as soon as the washer compresses evenly. Overdriving crushes the EPDM and destroys the seal.
Not suitable for fixing into timber — the self-drilling point is designed for steel substrates. For timber framing see our self-tapping wafer head range.
Suitable for
Loading delivery information...