Write a Review
RoofingPro RS50 Roofing Screws - 50mm - RAL 8004 Copper Brown
Description
The RoofingPro™ RS50 is a 50mm x 5.5mm hex head self-drilling roofing screw finished in RAL 8004 Copper Brown. It fixes profiled metal roofing and wall cladding sheets directly to light section steel without a pilot hole, and it does it in a colour that disappears against the sheet rather than sitting on top of it.
Built for roofing contractors, cladding installers and steel-frame fabricators working on commercial, industrial and agricultural envelopes. The No.3 self-drilling point cuts through steel up to 5mm thick, so purlins, rails and sheeting rails are all within range from a single fixing.
Where this screw earns its place is on visible elevations. A roof sheet or cladding panel is only as finished as the several hundred fixings holding it down, and a bright zinc head against a coloured sheet is the first thing the eye lands on.
Both the hex head and the EPDM sealing washer are powder coated in RAL 8004. Most coloured roofing screws stop at the head and leave a black rubber washer showing beneath it. This one does not.
Colour Matched in RAL 8004 Copper Brown
RAL 8004 is the colour most often used where planning conditions require a roof or cladding finish sympathetic to a rural or conservation context, so a visually quiet fixing matters more than usual.
Copper brown sits with brick, timber and terracotta. It is specified on agricultural buildings, rural workshops, heritage-sensitive schemes and brown profile roofing where a metal envelope needs to settle into a traditional setting. RAL 8004 Copper Brown is a warm muted terracotta brown, applied here to both the hex head and the sealing washer.
Because the coating goes on before the screw ever reaches site, there is no touching up, no spray cans and no colour drift between batches. The finish that leaves the box is the finish that stays on the roof.
Stocked as one of six core RoofingPro colours, with additional RAL references coated to order.
Site Applications
Typical applications on commercial, industrial and agricultural envelopes:
- Trapezoidal and box profile roof sheeting onto Z and C section purlins
- Vertical and horizontal metal wall cladding onto light section steel rails
- Roof repair and re-sheeting work where existing fixings have failed or corroded
- Coloured sheet installations where the fixing must match the panel finish
- Plant rooms, service enclosures and rooftop equipment housings
Typical fixing centres: 300mm - 500mm at sheet ends and 500mm - 1000mm at intermediate purlins (subject to sheet profile and wind loading).
Specification
Specification at a glance:
| Size | 5.5mm x 50mm |
| Head Type | Hex |
| Socket Size | 8mm |
| Point Type | Self-Drilling No.3 |
| Thread Type | 60° Self-Tapping |
| Effective Thread Length | 35mm |
| EPDM Washer | 16mm |
| FW Ø | 11mm |
| Max Drilling Thickness | 5mm |
| Material | Case & Core Hardened Carbon Steel |
| Substrate | Steel |
| Shank Finish | Bright Zinc Plated |
| Head & Washer Finish | Powder Coated |
| Colour | RAL 8004 Copper Brown |
Frequently Asked Questions
What are these screws for?
Fixing profiled metal roofing and wall cladding sheets to light section steel framing without pre-drilling, in a finish that matches the sheet.
Are the head and washer the same colour?
Yes, both are powder coated in RAL 8004 Copper Brown. Coating the EPDM washer as well as the head is what separates the RoofingPro range from a standard coloured tek screw.
What steel thickness can they handle?
Up to 5mm. Beyond that a higher-rated drill point or a pre-drilled hole is required.
Can I order a small quantity?
Yes. The range is sold by the unit, so you can order exactly what a job needs. Quantity breaks start at 200 screws.
Powder Coated Roofing Screws
We powder coat every RoofingPro screw ourselves. Coating an EPDM washer is an awkward, unpleasant process that most fixing suppliers will not take on, which is exactly why the majority of coloured roofing screws on the market still ship with a bare black washer.
The electrostatic powder is bonded to the substrate under heat rather than sitting on it as a film. The result survives socket contact, weathering and years of UV without chalking or flaking back to bright metal.
Benefits of powder coated roofing screws:
- Scratch resistant
- Rust resistant
- UV resistant
- Weather resistant
- Colourfast
Other RoofingPro RS50 Colour Options
RoofingPro™ RS50 roofing screws are stocked in six core RAL finishes matched to the most widely specified roofing and cladding colours, with further RAL references powder coated to order.
| tech_thread_type | Self Drilling (SD) |
|---|---|
| tech_head_style | Hex Head |
| tech_drive_type | 5/16 Hex Socket (8mm) |
| tech_length | 50mm |
| tech_diameter | 5.5mm |
| tech_gauge | No. 12 |
| tech_point_type | Self-Drilling No.3 |
| tech_steel_capacity | Up to 5mm total (Max Drilling Thickness) |
| tech_material | BZP Steel |
| tech_coating | Premium powder coat |
| tech_ral_code | RAL 8004 |
| tech_ral_name | Copper Brown |
| tech_colour_system | RAL Classic |
Recommended applications
Engineered for fixing profiled metal roofing and wall cladding sheets to light section steel framing on commercial, industrial and agricultural buildings. The powder coated hex head and colour-matched EPDM washer keep fixings visually consistent with the sheet across an entire elevation.
The No.3 self-drilling point cuts through steel up to 5mm without a pilot hole. Drive with an 8mm socket in a variable-speed driver and stop as soon as the washer compresses evenly. Overdriving crushes the EPDM and destroys the seal.
Not suitable for fixing into timber — the self-drilling point is designed for steel substrates. For timber framing see our self-tapping wafer head range.
Suitable for
Loading delivery information...