Write a Review
RoofingPro RS50 Roofing Screws - 50mm - RAL 9005 Jet Black
Description
Fixing a coloured roof sheet with an uncoated screw undoes the specification at the last step. The RoofingPro™ RS50 solves that: a 50mm x 5.5mm hex head self-drilling roofing screw with the head and the EPDM washer powder coated in RAL 9005 Jet Black.
The self-drilling No.3 point removes the pre-drilling step entirely. Drive straight into light section steel up to 5mm and the screw cuts, taps and seats in one operation, with 35mm of effective thread engaging behind the sheet.
At 50mm it suits deeper profiles and insulated build-ups where a shorter fixing runs out of thread before it reaches the steel. Box profile, corrugated and trapezoidal sheets all sit comfortably within its range.
Specified across roofing, cladding, rainscreen and agricultural work, where hundreds of fixings across an elevation either vanish into the finish or advertise themselves.
Colour Matched in RAL 9005 Jet Black
Black conceals weathering and staining better than any other finish, which makes it a common choice for rural and agricultural buildings where roofs are rarely cleaned. A matching black fixing keeps that low-maintenance logic intact.
Jet black has moved from agricultural sheeting into mainstream commercial and residential architecture. Black box profile roofs, dark standing seam, black rainscreen and contemporary barn conversions all specify RAL 9005. RAL 9005 Jet Black is a deep true black, applied here to both the hex head and the sealing washer.
Because the coating goes on before the screw ever reaches site, there is no touching up, no spray cans and no colour drift between batches. The finish that leaves the box is the finish that stays on the roof.
Stocked as one of six core RoofingPro colours, with additional RAL references coated to order.
Site Applications
Suited to the following work:
- Profiled steel and aluminium roof sheeting onto light section steel framing
- Wall cladding and rainscreen installation on commercial and retail units
- Re-roofing and overcladding projects onto existing steel structures
- Weatherproof fixing of coloured metal sheets where the seal is load-bearing
- Agricultural, equestrian and storage building envelopes
Typical fixing centres: 300mm - 500mm at sheet ends and 500mm - 1000mm at intermediate purlins (subject to sheet profile and wind loading).
Specification
Full technical specification for the RoofingPro™ RS50:
| Size | 5.5mm x 50mm |
| Head Type | Hex |
| Socket Size | 8mm |
| Point Type | Self-Drilling No.3 |
| Thread Type | 60° Self-Tapping |
| Effective Thread Length | 35mm |
| EPDM Washer | 16mm |
| FW Ø | 11mm |
| Max Drilling Thickness | 5mm |
| Material | Case & Core Hardened Carbon Steel |
| Substrate | Steel |
| Shank Finish | Bright Zinc Plated |
| Head & Washer Finish | Powder Coated |
| Colour | RAL 9005 Jet Black |
Frequently Asked Questions
Do these screws need a pilot hole?
No. The No.3 self-drilling point cuts its own hole through steel up to 5mm thick, so roofing sheets can be fixed directly to purlins and rails in a single operation.
Is the EPDM washer coloured as well as the head?
Yes. Both the hex head and the bonded EPDM sealing washer are powder coated in RAL 9005 Jet Black. Most coloured roofing screws leave the washer black.
What thickness of steel will they drill?
Up to 5mm maximum drilling thickness. That covers light section steel purlins, sheeting rails and most portal frame secondary steelwork.
What tool do I need to drive them?
An 8mm socket or nut driver in a variable-speed driver. Set the clutch so the washer compresses and seals without being crushed.
Powder Coated Roofing Screws
Every RoofingPro screw is powder coated at our own facility. That control is what lets us match a RAL reference properly and coat the washer alongside the head, rather than shipping a coloured head with a black rubber ring underneath it.
The powder is charged, applied dry and cured to a bonded finish. It resists chipping under the socket, resists chalking under UV and stays colourfast through the weathering cycles a metal roof sees every year.
Benefits of powder coated roofing screws:
- Scratch resistant
- Rust resistant
- UV resistant
- Weather resistant
- Colourfast
Other RoofingPro RS50 Colour Options
RoofingPro™ RS50 roofing screws are stocked in six core RAL finishes matched to the most widely specified roofing and cladding colours, with further RAL references powder coated to order.
| tech_thread_type | Self Drilling (SD) |
|---|---|
| tech_head_style | Hex Head |
| tech_drive_type | 5/16 Hex Socket (8mm) |
| tech_length | 50mm |
| tech_diameter | 5.5mm |
| tech_gauge | No. 12 |
| tech_point_type | Self-Drilling No.3 |
| tech_steel_capacity | Up to 5mm total (Max Drilling Thickness) |
| tech_material | BZP Steel |
| tech_coating | Premium powder coat |
| tech_ral_code | RAL 9005 |
| tech_ral_name | Jet Black |
| tech_colour_system | RAL Classic |
Recommended applications
Designed for metal envelope work: fixing box profile, corrugated and trapezoidal sheets to steel purlins and sheeting rails. Head and EPDM washer are both powder coated, so the fixing reads as part of the panel rather than sitting on top of it.
Self-drilling into light section steel up to 5mm, no pilot hole required. Use an 8mm nut setter at controlled speed and set the clutch so the washer seals without being crushed.
Not suitable for fixing into timber — the self-drilling point is designed for steel substrates. For timber framing see our self-tapping wafer head range.
Suitable for
Loading delivery information...