Write a Review
RoofingPro RS50 Roofing Screws - 50mm - RAL 7042 Traffic Grey
Description
Fixing a coloured roof sheet with an uncoated screw undoes the specification at the last step. The RoofingPro™ RS50 solves that: a 50mm x 5.5mm hex head self-drilling roofing screw with the head and the EPDM washer powder coated in RAL 7042 Traffic Grey A.
The self-drilling No.3 point removes the pre-drilling step entirely. Drive straight into light section steel up to 5mm and the screw cuts, taps and seats in one operation, with 35mm of effective thread engaging behind the sheet.
At 50mm it suits deeper profiles and insulated build-ups where a shorter fixing runs out of thread before it reaches the steel. Box profile, corrugated and trapezoidal sheets all sit comfortably within its range.
Specified across roofing, cladding, rainscreen and agricultural work, where hundreds of fixings across an elevation either vanish into the finish or advertise themselves.
Colour Matched in RAL 7042 Traffic Grey A
The RS50 in RAL 7042 Traffic Grey A is finished in a clean mid-tone neutral grey, powder coated across the hex head and the EPDM washer together.
Traffic grey is the mid-tone grey used across transport infrastructure, plant rooms, light industrial units and service buildings. It is bright enough to read as a deliberate finish rather than bare metal.
RAL 7042 is frequently specified alongside anthracite as a secondary or contrast colour, used on trims, flashings and lower panels where a lighter grey lifts an otherwise dark envelope.
Part of the six-colour RoofingPro core range held in stock, with a wider RAL palette available to order for matched schemes.
Site Applications
Specified across metal envelope work where the fixing is visible and the seal matters:
- Fixing profiled metal roofing sheets to steel purlins on industrial and commercial buildings
- Securing box profile and corrugated cladding to steel sheeting rails
- Agricultural roofing and barn cladding onto portal frame steelwork
- Fixing flashings, ridge caps, barge boards and eaves trims
- Insulated panel and composite sheet fixing where a deeper build-up needs the extra length
Typical fixing centres: 300mm - 500mm at sheet ends and 500mm - 1000mm at intermediate purlins (subject to sheet profile and wind loading).
Specification
Technical detail for specification and take-off:
| Size | 5.5mm x 50mm |
| Head Type | Hex |
| Socket Size | 8mm |
| Point Type | Self-Drilling No.3 |
| Thread Type | 60° Self-Tapping |
| Effective Thread Length | 35mm |
| EPDM Washer | 16mm |
| FW Ø | 11mm |
| Max Drilling Thickness | 5mm |
| Material | Case & Core Hardened Carbon Steel |
| Substrate | Steel |
| Shank Finish | Bright Zinc Plated |
| Head & Washer Finish | Powder Coated |
| Colour | RAL 7042 Traffic Grey A |
Frequently Asked Questions
Do I need to pre-drill?
No. The self-drilling No.3 point drills, taps and fixes in one pass through light section steel up to 5mm.
How weathertight is the seal?
The 16mm bonded EPDM washer compresses under the hex head as the screw seats, forming a permanent seal around the fixing hole. Drive it until the washer is evenly compressed and no further.
Will the colour fade?
Powder coating is heat-cured and bonded rather than sprayed on, so it holds colour through UV exposure and weathering far longer than painted or touched-up fixings.
What is the difference between this and the 38mm?
Length only. The 50mm carries 35mm of effective thread and suits deeper profiles or build-ups where a 38mm would not reach the steel.
Powder Coated Roofing Screws
RALfixings specialises in colour-matched visible fixings. Every RoofingPro screw is powder coated in-house, which lets us hold a genuine RAL match rather than an approximation, and lets us coat the EPDM washer as well as the head.
Powder coating is applied electrostatically as a dry powder and then cured, forming a bonded finish rather than a surface film. It will not chip off the hex flats under a socket the way wet paint does, and it holds colour through UV exposure far longer than a sprayed finish.
Benefits of powder coated roofing screws:
- Scratch resistant
- Rust resistant
- UV resistant
- Weather resistant
- Colourfast
Other RoofingPro RS50 Colour Options
RoofingPro™ RS50 roofing screws are stocked in six core RAL finishes matched to the most widely specified roofing and cladding colours, with further RAL references powder coated to order.
| tech_thread_type | Self Drilling (SD) |
|---|---|
| tech_head_style | Hex Head |
| tech_drive_type | 5/16 Hex Socket (8mm) |
| tech_length | 50mm |
| tech_diameter | 5.5mm |
| tech_gauge | No. 12 |
| tech_point_type | Self-Drilling No.3 |
| tech_steel_capacity | Up to 5mm total (Max Drilling Thickness) |
| tech_material | BZP Steel |
| tech_coating | Premium powder coat |
| tech_ral_code | RAL 7042 |
| tech_ral_name | Traffic Grey |
| tech_colour_system | RAL Classic |
Recommended applications
Designed for metal envelope work: fixing box profile, corrugated and trapezoidal sheets to steel purlins and sheeting rails. Head and EPDM washer are both powder coated, so the fixing reads as part of the panel rather than sitting on top of it.
Self-drilling into light section steel up to 5mm, no pilot hole required. Use an 8mm nut setter at controlled speed and set the clutch so the washer seals without being crushed.
Not suitable for fixing into timber — the self-drilling point is designed for steel substrates. For timber framing see our self-tapping wafer head range.
Suitable for
Loading delivery information...