Write a Review
RoofingPro RS50 Roofing Screws - 50mm - RAL 9016 Traffic White
Description
RoofingPro™ RS50 in RAL 9016 Traffic White: a 50mm x 5.5mm hex head self-drilling screw with a colour-matched EPDM sealing washer, made for fixing profiled metal sheets to light section steel.
The 50mm length is the workhorse of the range. It clears the crown of most box and trapezoidal profiles, passes through insulation build-ups and still lands 35mm of effective thread into the purlin behind.
Case and core hardened carbon steel with a bright zinc plated shank gives the drill point the hardness to cut steel and the shank the corrosion resistance to stay serviceable behind the sheet.
The powder coating is applied in-house to both the head and the washer, which is the part of this product that is genuinely difficult to do well and the reason most suppliers do not.
Colour Matched in RAL 9016 Traffic White
RAL 9016 Traffic White is a bright clean neutral white. Traffic white is the crisper, cooler white used across retail units, commercial rooflines, PVCu window and door systems, fascias, soffits and shopfitting. It reads brighter and more contemporary than RAL 9010.
RAL 9016 is one of the two most requested whites in the UK fixings market. On white cladding and trim, an uncoated fixing head shows as a dark speck from ground level across an entire elevation.
The powder coated head and washer are finished to the same RAL reference as the sheet, so the fixing reads as part of the panel rather than a fastener sitting on it. Across a full elevation that is the difference between a clean envelope and a dotted one.
All six core RoofingPro colours are held in stock for rapid dispatch, with a further range of RAL finishes coated to order.
Site Applications
Typical applications on commercial, industrial and agricultural envelopes:
- Trapezoidal and box profile roof sheeting onto Z and C section purlins
- Vertical and horizontal metal wall cladding onto light section steel rails
- Roof repair and re-sheeting work where existing fixings have failed or corroded
- Coloured sheet installations where the fixing must match the panel finish
- Plant rooms, service enclosures and rooftop equipment housings
Typical fixing centres: 300mm - 500mm at sheet ends and 500mm - 1000mm at intermediate purlins (subject to sheet profile and wind loading).
Specification
Technical detail for specification and take-off:
| Size | 5.5mm x 50mm |
| Head Type | Hex |
| Socket Size | 8mm |
| Point Type | Self-Drilling No.3 |
| Thread Type | 60° Self-Tapping |
| Effective Thread Length | 35mm |
| EPDM Washer | 16mm |
| FW Ø | 11mm |
| Max Drilling Thickness | 5mm |
| Material | Case & Core Hardened Carbon Steel |
| Substrate | Steel |
| Shank Finish | Bright Zinc Plated |
| Head & Washer Finish | Powder Coated |
| Colour | RAL 9016 Traffic White |
Frequently Asked Questions
Do I need to pre-drill?
No. The self-drilling No.3 point drills, taps and fixes in one pass through light section steel up to 5mm.
How weathertight is the seal?
The 16mm bonded EPDM washer compresses under the hex head as the screw seats, forming a permanent seal around the fixing hole. Drive it until the washer is evenly compressed and no further.
Will the colour fade?
Powder coating is heat-cured and bonded rather than sprayed on, so it holds colour through UV exposure and weathering far longer than painted or touched-up fixings.
What is the difference between this and the 38mm?
Length only. The 50mm carries 35mm of effective thread and suits deeper profiles or build-ups where a 38mm would not reach the steel.
Powder Coated Roofing Screws
We powder coat every RoofingPro screw ourselves. Coating an EPDM washer is an awkward, unpleasant process that most fixing suppliers will not take on, which is exactly why the majority of coloured roofing screws on the market still ship with a bare black washer.
The electrostatic powder is bonded to the substrate under heat rather than sitting on it as a film. The result survives socket contact, weathering and years of UV without chalking or flaking back to bright metal.
Benefits of powder coated roofing screws:
- Scratch resistant
- Rust resistant
- UV resistant
- Weather resistant
- Colourfast
Other RoofingPro RS50 Colour Options
RoofingPro™ RS50 roofing screws are stocked in six core RAL finishes matched to the most widely specified roofing and cladding colours, with further RAL references powder coated to order.
| tech_thread_type | Self Drilling (SD) |
|---|---|
| tech_head_style | Hex Head |
| tech_drive_type | 5/16 Hex Socket (8mm) |
| tech_length | 50mm |
| tech_diameter | 5.5mm |
| tech_gauge | No. 12 |
| tech_point_type | Self-Drilling No.3 |
| tech_steel_capacity | Up to 5mm total (Max Drilling Thickness) |
| tech_material | BZP Steel |
| tech_coating | Premium powder coat |
| tech_ral_code | RAL 9016 |
| tech_ral_name | Traffic White |
| tech_colour_system | RAL Classic |
Recommended applications
Built for fixing metal roofing and cladding to steel framing on commercial, industrial and agricultural envelopes. The 50mm length clears deeper profiles and insulated build-ups while still landing 35mm of effective thread into the steel.
Self-drilling No.3 point, no pre-drilling, steel up to 5mm. Use an 8mm socket in a variable-speed driver and seat the screw until the EPDM washer compresses evenly around the head.
Not suitable for fixing into timber — the self-drilling point is designed for steel substrates. For timber framing see our self-tapping wafer head range.
Suitable for
Loading delivery information...